Area calculator: measure shapes, convert units and combine sections
Identify the surface you want to measure
Area describes the size of a two-dimensional surface. It is different from the distance around that surface and different again from the volume of a solid. A room's floor area, a rectangular panel and a circular garden bed are all area questions. The calculator begins with a shape because the relationship between dimensions depends on geometry. Choose the shape that describes the surface, then enter the measurements requested for that shape rather than choosing whichever form happens to accept the numbers you already have.
The available shapes are rectangle, square, triangle, circle, ellipse, trapezoid, parallelogram and circular sector. These cover many straightforward measurement tasks and can also serve as pieces of a more complicated layout. The result includes the selected square unit and several conversions. A diagram helps identify the meaning of dimensions, but it is illustrative rather than a survey or scale drawing. Your actual measurements remain the basis of the answer, so check the shape and dimensions before interpreting a precise-looking numerical result.
Keep length units consistent
All length fields within one calculation use the selected unit. The initial unit is feet, with inches, yards, meters, centimeters and millimeters also available. Do not enter one side in feet and another in inches while leaving the selector on feet. A twelve-foot length and a ten-foot width produce one hundred twenty square feet. If the width is actually ten inches, the corresponding floor area is much smaller. The unit selector is part of the input, not merely a preference for displaying the final number.
Changing the selector converts existing dimensions so that the represented physical size stays the same. For example, twelve feet becomes 3.6576 meters. The sector's angle remains in degrees because it is not a length. Exact numeric fields preserve typed measurements independently of slider increments. A dimension of 12.75 feet can be entered directly; you do not need to round it to thirteen. Be careful with decimal feet: twelve feet nine inches is 12.75 feet, while 12.9 feet represents a different length.
Calculate rectangles and squares
For a rectangle, multiply length by width. Both dimensions must describe perpendicular sides of a shape with right-angle corners. A twelve-foot by ten-foot rectangle has an area of one hundred twenty square feet. Its perimeter is twice the sum of those dimensions, or forty-four feet. The calculator shows perimeter for this shape because the entered dimensions fully determine it. Area uses square units, while perimeter uses ordinary length units, so the two answers should not be confused when estimating material.
A square is a rectangle whose sides have equal length. Its area is the side multiplied by itself, and its perimeter is four times the side. A six-foot square has thirty-six square feet of area and twenty-four feet of perimeter. If your measured sides differ, use Rectangle instead of averaging them and calling the result a square. An average side length can hide a shape mismatch. For a real surface that is not quite rectangular, divide it into measured pieces or use a measurement method appropriate to its actual outline.
Use perpendicular height for triangles
The triangle mode asks for a base and the perpendicular height to that base. Multiply those two values and divide by two. A base of twelve feet with a perpendicular height of eight feet gives forty-eight square feet. The height is not necessarily one of the triangle's sloping sides. It is the shortest distance from the opposite vertex to the line containing the chosen base. For some triangles, that perpendicular meets an extension of the base outside the drawn edge.
This distinction is a common source of measurement errors. Entering a sloping side as the height usually produces the wrong area even though the arithmetic runs correctly. The illustrated triangle marks a base-and-height relationship, not every possible triangle orientation. The tool does not derive a triangle's area from three side lengths or calculate its perimeter from the two supplied measurements. A base and perpendicular height determine the area but do not uniquely determine all sides. If only side lengths are known, this particular mode does not supply the missing height.
Choose radius or diameter for circles
Circle area equals pi multiplied by the square of the radius. The radius runs from the center to the edge. The diameter crosses the entire circle through the center and is twice the radius. The checkbox lets you enter diameter instead, with the calculator dividing that measurement by two before using the area formula. Switching between radius and diameter converts the existing value, preserving the same circle rather than suddenly doubling or halving its physical size.
For a radius of three feet, the area is nine times pi, approximately 28.274334 square feet. The boundary length is two times pi times the radius, approximately 18.849556 feet. If you mistakenly enter a six-foot diameter into a radius field, the area becomes four times too large because the radius is squared. Read the field label before calculating. A circular outline in the diagram is helpful, but it cannot detect whether a measurement taken in the real world was from edge to edge or center to edge.
Read ellipse measurements as semi-axes
The ellipse mode uses two semi-axis lengths. Each semi-axis runs from the center to the edge along one of the ellipse's principal directions. These are half of the full width and half of the full height measured along those directions. The formula is pi multiplied by semi-axis a and semi-axis b. If the full major dimension is twelve feet and the full minor dimension is eight feet, enter six and four, giving twenty-four times pi square feet.
Entering both full dimensions instead would multiply the correct area by four. The labels deliberately include the word semi-axis to make the required measurements explicit. When the two semi-axes are equal, the ellipse becomes a circle and the same formula reduces to pi times radius squared. The calculator does not show an ellipse perimeter because a simple perimeter expression is not part of this mode. Use the area result for surface calculations, and do not treat it as the amount of edging needed around an elliptical outline.
Measure parallel bases and height for a trapezoid
A trapezoid's area is the average of its two parallel base lengths multiplied by the perpendicular distance between them. The calculator asks for base a, base b and that height. Bases of ten feet and six feet with a height of four feet produce thirty-two square feet. The bases must be parallel for this formula to represent the intended shape. A sloped side connecting the bases is not the height unless it is also perpendicular to the bases.
The diagram shows a familiar centered trapezoid, but the formula also works when one base is shifted sideways relative to the other. That shift does not change the area when base lengths and perpendicular height remain unchanged. It does change the sloping side lengths, which is why the tool does not infer a perimeter from these three inputs. If you are estimating trim, fencing or edging, measure those sides separately. A complete area calculation does not automatically provide a complete boundary measurement.
Use base and height for a parallelogram
A parallelogram has opposite sides that are parallel. Its area is base multiplied by perpendicular height. Sliding the top edge sideways without changing the base or vertical height does not change its area. This is the geometric reason the formula resembles a rectangle's formula even though the sides may be slanted. A ten-foot base with a four-foot perpendicular height has forty square feet of area, regardless of the depicted slant within a valid parallelogram.
Do not substitute the sloping side length for height. The sloping side is generally longer than its perpendicular component, and using it would overstate the surface. The diagram includes a height indicator to distinguish these dimensions. It uses a schematic slant because the entered base and height do not determine a unique parallelogram. Consequently, no perimeter is displayed for this mode. You can calculate a useful area from the two supplied measurements while recognizing that other geometric features remain unknown.
Calculate a circular sector
A sector is the portion of a circle bounded by two radii and an arc. The calculator uses a radius and an angle in degrees. Its area equals the full circle's area multiplied by the angle divided by three hundred sixty. A ninety-degree sector therefore contains one quarter of the corresponding circle's area. With a radius of four feet, that area is four times pi square feet. The angle field accepts values from zero through three hundred sixty degrees.
A zero-degree sector has zero area. At three hundred sixty degrees, the result represents the full circle, and the boundary is its circumference rather than a circumference plus two duplicate radii. For intermediate angles, the boundary includes the arc and both radii. The angle remains unchanged when you switch the length unit. This mode assumes a circular sector, not an irregular curved wedge. If the boundary follows a different curve or the two sides do not meet at the circle's center, this formula does not describe that surface.
Convert square units by squared length factors
Area conversion squares the corresponding length conversion factor. Since one foot equals 0.3048 meters, one square foot equals 0.3048 squared square meters. This explains why converting a square-foot result is not the same as multiplying by the ordinary feet-to-meters factor. Likewise, one square yard contains nine square feet because a yard is three feet in each direction. The calculator handles those factors internally and presents square feet, square meters and square yards together for comparison.
Acres and hectares are also included for larger surfaces. The acre conversion here uses the international-foot relationship of 43,560 square feet per acre. A hectare is ten thousand square meters. These conversions do not turn an approximate measurement into a legal land survey. Older records or specialized surveying systems may use conventions that require separate interpretation. For an ordinary planning calculation, retain the original dimensions and units with the result so a reviewer can see the measurement basis rather than only a converted area.
Combine separate sections without duplicating space
The Combine sections panel saves the current valid shape as an added or subtracted area. This is useful for a layout that can be split into rectangles, triangles or other supported shapes. A large rectangle with a rectangular cutout can be represented by adding the outer rectangle and subtracting the cutout. Each saved section keeps its area independently of later edits to the current shape. Changing a dimension in the main form does not silently rewrite a section that was already saved.
Sections should not overlap unless the overlap is deliberately accounted for. Adding two overlapping rectangles counts their shared region twice. You can subtract a correctly measured overlap, but the calculator does not know the locations of the shapes and cannot detect overlap automatically. It stores numerical areas, not a floor-plan drawing. Label sections clearly, check their operations and remove an incorrect row before relying on the combined total. Up to forty sections are supported, and the total is shown in square feet and square meters.
Review subtraction and zero-area cases
Subtracting more area than you have added produces an error for the combined result. The tool does not convert the negative total to a positive surface or quietly discard the excess deduction. The saved rows remain visible so that you can identify and remove an incorrect subtraction. A current shape can still be valid while the saved combination is invalid; these are separate calculations. The main shape result and the combined result should therefore be read with their respective labels and error messages.
Zero dimensions are permitted and produce zero area under the relevant formula. This can be useful while exploring a boundary case, but it normally does not describe a surface you need to cover. Missing or invalid values are different from zero and require correction. The form clears outdated shape results when inputs are invalid. A zero-size diagram may still use an illustrative outline with labels, so rely on the numerical result rather than assuming the schematic drawing has a physical scale. The page explicitly identifies the drawing as illustrative.
Use area as one input to a material estimate
An area result is often only the starting point for purchasing material. Flooring, tile, fabric, seed and paint can require allowances, package rounding or coverage assumptions that differ by product and project. This calculator reports geometry and conversions; it does not add a universal waste percentage or estimate a product's performance. For paint, the related Paint Calculator accepts coverage, coats, openings and container sizes separately. Keeping those assumptions outside the geometric area makes it easier to see why a purchase quantity differs from the measured surface.
Before saving or sharing a result, check the shape, unit, perpendicular dimensions and any radius-versus-diameter choice. For combined sections, retain a record of the individual pieces and their add or subtract signs. The page does not persist a floor plan or save sections to an account, so copy the information you need before clearing them or leaving. A reliable area calculation is reproducible from clear measurements and a suitable formula. The calculator can carry out that formula, but it cannot verify the physical shape or measurement technique behind the entries.